NonVtec Honda Forums • View topic

sml_blk · **Posted:** Wed May 14, 2008 4:28 pm

check this out, im lookin the final drive for a d series like either a zc final drive or for a civic dx/lx/cx/vx, i wanna know how many teeth on the gear, when i race i use 1st gear for like 10ft, and go straight to 2nd, the motor mostly makes a lotta tq, thats all it is a bunch of tq, i wanna get it dynoed to see how much tq it makes, but anyway, with the fx500 clutch system i can launch the car in 2nd gear (without burnin up the cltuch and spin the tires) and it moves, but with close gears its not really doing nothin it run quicker with taller gears, if i can get like a 45-50mph 1st gear or change my final drive to compensate, i'll be runnin nitrous anyway, thats why im really think about just the final drive, if u know where to find one for me then that'll do, or if u know a website that tells how many teeth on the gear, i know the zc final drive is 70/18 = 3.888, i had a ls trans with a 66/15=4.4, and now i got a 64/15=4.26, and i runs better, but i need something taller, if i can get a zc 3.888 i'll be fine or get a 18tooth main shaft i'll be fine then 66/18=3.67, well damn thats alotta typin, but if u have anything or can find something for me let me know

mp82 · **Posted:** Wed May 14, 2008 6:58 pm

USDM Si Tranny JDM ZC Tranny
First 3.250 3.250
Second 1.894 1.944
Third 1.259 1.346
Fifth .771 .878
Final Drive 4.25 3.88

usdm si tranny (68/16 = 4.25)
zc tranny (70/18 = 3.88) as you mention.

88-91 CRX Si
1st 3.250
2nd 1.894
3rd 1.259
4th 0.937
5th 0.771
Final Drive 4.250

88-91 CRX DX
1st 3.250
2nd 1.894
3rd 1.259
4th 0.937
5th 0.771
Final Drive 3.888 (88 DX: 3.722)

88-91 CRX HF
1st 3.250
2nd 1.650
3rd 1.033
4th 0.823
5th 0.694
Final Drive 2.954 (3.250 in California)

88-91 CRX ZC DOHC (JDM)
1st 3.250
2nd 1.944
3rd 1.346
4th 1.033
5th 0.878
Final Drive 3.888

90-93 Integra ZC SOHC (JDM)
1st 3.250
2nd 1.894
3rd 1.259
4th 0.937
5th 0.771
Final Drive 4.250

90-93 Integra ZXi ZC SOHC (JDM)
1st 3.250
2nd 1.894
3rd 1.259
4th 0.937
5th 0.771
Final Drive 4.437

ok too much to type hope this help
http://www.knology.net/~jediklc/gearratiosdseries.htm

sml_blk · **Posted:** Thu May 15, 2008 6:59 am

i wonder if the shafts would fit in a bseries trans without any prolems, like my s1 trans

mp82 · **Posted:** Thu May 15, 2008 6:24 pm

I do not think it's gonna work. Its different.

sml_blk · **Posted:** Fri May 16, 2008 8:18 am

i need a better gear ratio than i do now, something taller, i need like a 58 tooth gear for my ring gear then i have like a 3.866 gear, or get a type-r trans and use its 2nd in my first gear, and it 3rd and so on

sml_blk · **Posted:** Fri May 16, 2008 8:26 am

if i can find a way to get my 1st gear ratio like between 2.8 to 2.4 then that'll make me happy

gsRnonVTEC · **Posted:** Sun Nov 30, 2008 8:40 pm

That Is a LOTSA wires my friend. looks like spaghetti, but good luck on the process

Similar topics
Topic title	Forum	Author	Replies
F20B SOHC Non-Vtec Head on F22B SOHC Non-Vtec Block	F & H Series Engine Chat	nheri18	8
how do you remove dipstick tube on block	B Series Engine Chat	jeNNer4ce	0
ANNOUNCING MITCHWORKS VACUUM BLOCK!	Off Topic	mp82	11
B20 PR8 head, ls block, gsr head/block, tranny parts etc	Classifieds	ruffrhyder	1
what you guys think of my b18b block fully built .....	Build Threads	imsleepn	71
Another will this block work with this head thread...	B Series Engine Chat	masterbeavis	1
b18 vs b20 block stength	B Series Engine Chat	Dohc_Hatch	3
b20 block with ls head?	B Series Engine Chat	4doorls	2
b18b block out of 96 integra pr4 head problems	B Series Engine Chat	jarred69	3
how to make and ls vtec from a b18a1 block b16a head	Build Threads	Frank	1

small block b20

Who is online